Zapisz na liście zakupowej
Stwórz nową listę zakupową

Dodaj produkty podając kody

Dodaj plik CSV
Wpisz kody produktów, które chcesz zbiorczo dodać do koszyka (po przecinku, ze spacją lub od nowej linijki). Powtórzenie wielokrotnie kodu, doda ten towar tyle razy ile razy występuje.
Grundfos Zestaw podnoszenia ciśnienia Hydro MPC-F 2 CRI 15-3 96941210

Grundfos Zestaw podnoszenia ciśnienia Hydro MPC-F 2 CRI 15-3 96941210

  • Zestawy podnoszenia ciśnienia z zewnętrznymi przetwornicami częstotliwości
RozmiarCena / szt.RabatDostępność i wysyłkaKup za punktyIlość
84 199,22 zł brutto
Cena katalogowa: 129 537,27 zł
Rabat
Zapytaj o cenę i dostępność ( Oferowana cena może się różnić w przypadku pojawienia się produku na magazynie)
Zapytaj o cenę i dostępność ( Oferowana cena może się różnić w przypadku pojawienia się produku na magazynie)
Kup za punkty
Suma wybranych produktów:
(Zniżka %)
0
brutto / 1szt.
/ 1szt.
Ten produkt nie jest dostępny w sklepie stacjonarnym
Bezpieczne zakupy
Po zakupie otrzymasz pkt.
Hydro MPC-F 2 CRI 15-3

Pressure booster system supplied as compact assembly according to DIN standard 1988/T5.

The pumps are CR(I) pumps connected to one external Grundfos CUE frequency converter. The speed-controlled operation alternates between the pumps.

  • Hydro MPC-F maintains a constant pressure through continuous adjustment of the speed of the pump connected to the CUE frequency converter.
  • The system performance is adapted to the demand through cutting in/out the required number of CR(I) pumps and through parallel control of the pumps in operation.
  • Pump changeover is automatic and depends on load, time and fault.

The system consists of these parts:
:vertical multistage centrifugal pumps, type CRI 15-3 with one external frequency converter.

  • One pump is frequency-converter controlled; the others are mains-operated (start/stop)
  • CRI pump parts in contact with the pumped liquid are made of stainless steel.
  • CR pump bases and heads are of cast iron; other vital parts are made of stainless steel.
  • Pump bases and heads are of either cast iron/stainless steel (CRI) or cast iron EN-GJS-500-7 (CR), depending on pump type; other vital parts are made of stainless steel EN DIN 1.4301.
  • The pumps are equipped with a service-friendly cartridge shaft seal, HQQE (SiC/SiC/EPDM).
  • Two manifolds of stainless steel EN DIN 1.4571.
  • Base frame of stainless steel EN DIN 1.4301 up to CR 64. Above CR 64 the pumps are placed on a galvanized C-profile frame.
  • One non-return valve (POM) and two isolating valves for each pump.
  • Non-return valves are certified according to DVGW, isolating valves according to DIN and DVGW.
  • Adapter with isolating valve for connection of diaphragm tank.
  • Pressure gauge and pressure transmitter (analog output 4-20 mA).
  • Control MPC in a steel cabinet, IP 54, including main switch, all required fuses, motor protection, switching equipment and microprocessor-controlled CU 352.

Dry-running protection and diaphragm tank are available according to the list of accessories.

Pump operation is controlled by Control MPC with the following functions:

  • Intelligent multipump controller, CU 352.
  • Constant-pressure control through continuously variable adjustment of the speed of each individual pump.
  • PID controller with adjustable PI parameters (Kp + Ti).
  • Constant pressure at setpoint, independent of inlet pressure.
  • Soft pressure build-up (To prevent water hammer during startup).
  • On/off operation at low flow.
  • Automatic cascade control of pumps for optimum efficiency.
  • Selection of min. time between start/stop, automatic pump changeover and pump priority.
  • Automatic pump test function to prevent idle pumps from seizing up.
  • Possibility of standby pump allocation.
  • Possibility of backup sensor (redundant primary sensor).
  • Secondary sensor (Possible to switch to another sensor/setpoint).
  • Multi-sensor (up to 6 sensors to influence the setpoint).
  • Manual operation.
  • Possibility of external setpoint influence.
  • Log function.
  • Setpoint ramp.
  • Possibility of digital remote-control functions:
  • System on/off.
  • Max., min. or user-defined duty.
  • Up to 6 alternative setpoints.
  • Digital inputs and outputs can be configured individually.
  • Pump and system monitoring functions:
  • Minimum and maximum limits of current value.
  • Inlet pressure.
  • Motor protection.
  • Sensors and cables monitored for malfunction.
  • Alarm log with the previous 24 warnings/alarms.
  • Display and indication functions:
  • Colour screen display.
  • Green indicator light for operating indications and red indicator light for fault indications
  • Potential-free changeover contacts for operation and fault.
  • Grundfos bus communication.

It is possible to add CIM communication modules for communicating with Scada/BMS.

Pumps, piping, cabling complete as well as Control MPC are mounted on the base frame. The booster system has been preset and tested.

Zestawy podwyższania ciśnienia - opcje.

Wydajność:  Woda
Dopuszczalna temp. cieczy:  5 °C .. 60 °C
Max. ciśnienie robocze:  16 bar
Wydajność (Pompownia):  47 m³/h
Wydajność bez 1 pompy Wydajność bez 1 pompy
Prąd znamionowy:  12.9 A
Moc nominalna:  3 kW
Masa netto:  257 kg
Moc nominalna Zbiorniki membranowe, zabezpieczenie przed suchobiegiem i sterowniki patrz osprzęt.

Symbol
96941210
Kod producenta
5700314237400
Oferta dla Ciebie

 

Zadzwoń tel.: 662-586-615  lub napisz na 

sklep@akwa-terma.com.pl 

w sprawie indywidualnej oferty.

 

MODEL
HYDRO MPC-F
Potrzebujesz pomocy? Masz pytania?Zadaj pytanie a my odpowiemy niezwłocznie, najciekawsze pytania i odpowiedzi publikując dla innych.
Zapytaj o produkt
Jeżeli powyższy opis jest dla Ciebie niewystarczający, prześlij nam swoje pytanie odnośnie tego produktu. Postaramy się odpowiedzieć tak szybko jak tylko będzie to możliwe. Dane są przetwarzane zgodnie z polityką prywatności. Przesyłając je, akceptujesz jej postanowienia.
Napisz swoją opinię
Twoja ocena:
5/5
Dodaj własne zdjęcie produktu:
Prawdziwe opinie klientów
4.9 / 5.0 8 opinii
pixel